|
|
Cruiser
Posts: 100
| instead of spending $79.00 for cam tension cover my buddy Eddie from CCUPOWERSPORTS.COM suggested lug nut covers that go on a semi-truck! I bought a pair at the local truck stop for a dollar a piece!! they fit great and look good to boot!
(2012-01-17_11.34.30.jpg)
(2012-01-17_11.08.39.jpg)
Attachments
----------------
 2012-01-17_11.34.30.jpg (81KB - 1 downloads)
2012-01-17_11.08.39.jpg (46KB - 6 downloads)
|
|
| |
|
Visionary
Posts: 1365
Central Maryland | Now THAT is a Cool Idea !!! Thanks! |
|
| |
|
Visionary
Posts: 1229
Rancho Cucamonga, CA | WTG!! Mine came with them, but I'll tell my friends. How do you secure them? or does the press fit hold ok?
Edited by Nozzledog 2012-01-17 5:09 PM
|
|
| |
|
Visionary
Posts: 3773
Pittsburgh, PA | Nozzledog - 2012-01-17 5:07 PM
WTG!! Mine came with them, but I'll tell my friends. How do you secure them? or does the press fit hold ok?
i was wondering the same thing.. because the victory ones have a set screw in them to secure it . |
|
| |
|
Iron Butt
Posts: 763
Anderson, IN (48mi NE of downtown Indianapolis) | You can make all the bolt heads on your bike chrome, flames, cross, skull, or eagle.
http://www.boltdepot.com/Metric_chrome_bolt_covers_and_Hole_plugs.a... |
|
| |
|
Cruiser
Posts: 232
| What size you buy? |
|
| |
|
Cruiser
Posts: 100
| They just press on no set screw, my friend that told me about them has had his for a while now and never lost one! I stopped at Love's truck stop and they had 3 styles. these had no lip on them and they were shorter!! I posted this on the VMC as well and someone said there might be a different for new trucks. but mine fit perfect!
Edited by Blister 2012-01-17 7:54 PM
|
|
| |
|
Visionary
Posts: 8144
New Bohemia, VA | Thanks... |
|
| |
|
Cruiser
Posts: 88
Nova Scotia , Canada | Great Idea
Thanks Don |
|
| |
|
Cruiser
Posts: 96
Princeton, IL | I love innovative and cheap ideas. Great post, thanks! |
|
| |
|
Tourer
Posts: 500
| I stopped at the I-80 World's Largest Truck Stop in Iowa a couple years ago and was "awe-struck" at the size of the place and the stuff they sell...I bought all the chrome nut covers I needed for just about every bolt on my bike, including cam chain covers, axle covers, engine mount covers, etc. etc. they all fit with no problems and cost me $23 for the whole deal....If you go that way measure the bolt covers sizes you need beforehand then go for it...As stated above most are for trucks, but they work great and look just fine.....I also think they can be found on the Web...... |
|
| |
|
Tourer
Posts: 366
Albuquerque, NM | I remembered ordering from this site as per Thomas on his fork bullet tip install in the tech ref forum. They should have something that will fit the cam tensioner covers. (thanks again Thomas)
http://www.empirechromeshop.com/p-6859-33mm-chrome-plastic-bullet-s...
Fork Bullet Install Thread:
http://www.vision-riders.com/bb/forums/thread-view.asp?tid=5149&pos...
Edited by nailer 2012-01-18 2:19 PM
|
|
| |
|
Visionary
Posts: 4278
| If your scared they'll come off put some silicon on the side of the nuts |
|
| |
|
Central Wisconsin | Darren thanks for the tip. I think I'll try covering up the CTN's. Randy, My fork bullets have been holding up well. I did drill a tiny hole in the tips to allow water drainage. Thanks for reminding me about the plastic chrome nut cover website too.
|
|
| |