|
|
Puddle Jumper
Posts: 42
Prescott, AZ | sgiacci - 2012-02-29 2:17 PM
Xbike trunk mount kit.
Heated backrest (driver and passenger), heated passenger armrests.
I thought everyone hated the look of the Xbike trunk mount kit. I know it I do. I would like a quick release, but don't it as ugly as the XBike's.
I think heated backrests are a great idea. |
|
| |
|
Puddle Jumper
Posts: 16
Sydney - AUSTRALIA | Oh one more thing that I can think of is a Centre Stand similar to the third party stand by Ezy Up for the HD. It's a great stand and I only wish they'd make one for the XCT. From all accounts the Victory and other third party centre stands aren't up to scratch.
|
|
| |
|
Visionary
Posts: 1632
Jasper, MO | Easy-Up center stand, as long as it doesn't lose any cornering clearance. I don't care if you can operate it while sitting on the bike or not, as long as it gets the rear tire off the ground. Given the long suspension travel of the Vision/Cross bikes, a two-stage stand like the ones on the old Kawasaki Voyager XII might be a solution.
On board rear suspension air pressure pump and adjustment. Maybe double as an air supply for tire inflation, but not a requirement. On-the-go rear suspension adjustment and pressure readings would be nice.
Ronnie |
|
| |
|
Iron Butt
Posts: 965
New York State | The Police variation of the Ness Bash plate |
|
| |
|
Cruiser
Posts: 56
| A luggage rack for a Vision Tour that does not cost me a kidney to get. I bought a HD trunk rack for my 07 Kingpin Tour at the HD dealer for $140 that worked perfectly. Rounded chrome bars that were about 1/4 to 1/2 inch thick with plenty of cross members and tie down spots. Doesnt need to be super elegant...just work and enable me to carry my wifes crap on a long weekend. Why does everyone think trunk racks should be $400 for these bikes? Please help! Thanks |
|
| |
|
Cruiser
Posts: 56
| Wanted to add...
1)Brackets for lights under the driving light of the Vision
2)Adustable rear pegs for passenger to move around on long rides.
3)Did I mention an affordable trunk rack?
4)Prepainted gauge bezel for Vison to replace stock "black" bezel. Both pieces...around speakers and chrome piece around gauges.
5)Flag mount for proposed trunk luggage rack.
6)Handle bar mount for extra cig lighter so I can charge my phone without opening glove box.
7)Quick disconnect for trunk.
8)Cup holder that goes on opposite side of handle bars...not right in front of me.
Thanks again.
Edited by kpVision 2012-03-15 3:45 PM
|
|
| |
|
Tourer
Posts: 401
| Reverse that will work on all model year Visions and Xbikes. |
|
| |
|
Puddle Jumper
Posts: 10
| OK...here's what I would REALLY like to see some vendor tackle.
Heat Deflectors that fit on the tank and along the side covers LIKE THE NEW 2013 Harley's have put on all their touring bikes. THIS IS NEEDED BADLY!
A small shield that latches into the holes on the speaker that puts an "awning" over the speaker. Something that could be put on and off easily. Kind of like you see on car windows to allow for the window to be rolled down while it's raining...this would work on the same principle. |
|
| |
|
Tourer
Posts: 537
, FL United States | One goodie I would like is to have someone like Llyod or Kevin a little closer that can do some work on my bike instead of a 5 hour trip one way. Then maybe I could get the cams, bigbore kit, some tuning or hell being that close I might opt for a nitrous bottle. |
|
| |
|
Cruiser
Posts: 231
Desert Hot Springs (Palm Springs area), CA | kpVision - 2012-03-15 3:44 PM Wanted to add... 1)Brackets for lights under the driving light of the Vision 2)Adustable rear pegs for passenger to move around on long rides. 3)Did I mention an affordable trunk rack? 4)Prepainted gauge bezel for Vison to replace stock "black" bezel. Both pieces...around speakers and chrome piece around gauges. 5)Flag mount for proposed trunk luggage rack. 6)Handle bar mount for extra cig lighter so I can charge my phone without opening glove box. 7)Quick disconnect for trunk. 8)Cup holder that goes on opposite side of handle bars...not right in front of me. Thanks again. I've a solution for #8)Cup holder that goes on the opposite side of handle bars. I put a Kruzer Kaddy (in black) on my left handlebar, just next to the clutch. Here is a picture. It works great! 
|
|
| |
|
Visionary
Posts: 1229
Rancho Cucamonga, CA | ArkieBiker - 2012-03-18 9:46 AM
Heat Deflectors that fit on the tank and along the side covers LIKE THE NEW 2013 Harley's have put on all their touring bikes. THIS IS NEEDED BADLY!
Something like this?...
(2011-04-01 14.28.27a.jpg)
Attachments
----------------
 2011-04-01 14.28.27a.jpg (89KB - 19 downloads)
|
|
| |
|
Puddle Jumper
Posts: 10
| OK Nozzledog FESS UP. Where'd you get such a rare item like that? INQUIRING MINDS want to know. :-) |
|
| |
|
Visionary
Posts: 4278
| Vision models
chrome shifter rod with ends
chrome bolts for front rotors
nicer oil dipstick
02 sensor covers ones that will slip over with out having to take them out to install the covers
chrome cover for the gear indecator behind the rear cylinder
chrome master clinder cover for the body and and clutch
|
|
| |
|
Cruiser
Posts: 215
W'ford Tx | +1billion for a body kit to make the side bags bigger. |
|
| |
|
Cruiser
Posts: 249
Phenix City AL. | passenger high way peg mounts, I make a set if you are interested
passenger cup holders, their is a thread on how to install a ram mount to the speaker covers, to allow a ram mount cup holder I could make a kit to include 1 ram mount, 4 mounting bolts, 1 backing plate, and a template to drill the holes.
lite mounts, how about mounting driving lites to the tip overs on the front, I might have something for that.
Riders cup holder that mount to the front of the resivors, that is mounted using the mirror holes, I made my mount, I could make more.
I am not trying to take anyones thunder, parts or ideas , just trying to help get some cool stuff out. |
|
| |
|
Cruiser
Posts: 215
W'ford Tx | Sounds good jb for the cup holder but us with 08s don't have that option. I've seen one on eBay for $70 but don't know exactly how it works and don't want to pay that much to find out if it works or not. |
|
| |
|
Cruiser
Posts: 249
Phenix City AL. | A regular drill, and a tap set, would allow you to drill and tap your 08, I have 08 controls on my 09, that I drilled and tapped, ride over to Alabama, and I will do yours lol |
|
| |
What Bagger parts do you want to see?
