|
|
Cruiser
Posts: 74
MN. | Is this an easy off piece? I like the look, but am wondering where it attatches and if it pops off easily. Thanks. |
|
| |
|
Fountain Inn, SC United States | Check the Tech Reference section of this site. There is a Installation note on the luggage rack. |
|
| |
|
Tourer
Posts: 319
| Thats the most expensive backrest/ rack combo in history.......  |
|
| |
|
Cruiser
Posts: 296
Central Florida | BATMAN - 2008-05-17 7:23 AM
Is this an easy off piece? I like the look, but am wondering where it attatches and if it pops off easily. Thanks.
NOT at all.... you have to remove trunk(duh) and passenger back rest bolts into 4 holes in frame.
the luggage rack bolts onto back rest and should be done before you bolt down backrest.
to top it off you have to cut out 2 grooves in closeout panel(dremel cut off wheel or jig saw)
Measure twice and cut once....
mine is off by about 1/8 in on one side... |
|
| |
|
Puddle Jumper
Posts: 41
| Is there a driver backrest available?
|
|
| |
|
Cruiser
Posts: 296
Central Florida | akabubba42 - 2008-05-17 8:40 PM
Is there a driver backrest available?
NOT from Victory. Utopia makes one and several members have them. do a search for Utopia backrests |
|
| |
|
Visionary
Posts: 1324
So Cal | devilboy - 2008-05-17 3:26 PM
BATMAN - 2008-05-17 7:23 AM
Is this an easy off piece? I like the look, but am wondering where it attatches and if it pops off easily. Thanks.
NOT at all.... you have to remove trunk(duh) and passenger back rest bolts into 4 holes in frame.
the luggage rack bolts onto back rest and should be done before you bolt down backrest.
to top it off you have to cut out 2 grooves in closeout panel(dremel cut off wheel or jig saw)
Measure twice and cut once....
mine is off by about 1/8 in on one side...
1/8"? Dont be getting all anal on us now. |
|
| |
|
Cruiser
Posts: 235
Evergreen, CO | When I got the passenger backrest and panel, it came with a template that was pretty easy to center, then stick to the underside of the panel. I just followed the lines, and all was well. Getting the rubber grommet that is around the "sissy bar" portion of the backrest to seat properly around the edges in the cuts on the panel was a bit of a PITA, but it still only took me around 10 minutes to get everything seated properly. I keep mine in "street" mode unless we are going on a multi-day trip, then it's out with the passenger backrest, on with the "pod". |
|
| |
|
Visionary
Posts: 1484
LaPorte,Tx. | I have seen two types of rider back rests for the Vision, in the first phote, Chandler Tom has this type which is very nice, but somewhat high maintenance.
In the second photo you have the type I have which is lower in maintenance cost, but has a lot less features. Both are Visionary. 
|
|
| |
|
Visionary
Posts: 1484
LaPorte,Tx. | I have seen two types of rider back rests for the Vision, in the first phote, Chandler Tom has this type which is very nice, but somewhat high maintenance.
In the second photo you have the type I have which is lower in maintenance cost, but has a lot less features. Both are Visionary.
|
|
| |
|
Puddle Jumper
Posts: 41
| LMAO...........would love the first but would settle for the second........LMAO
|
|
| |
|
Cruiser
Posts: 296
Central Florida | cjnoho - 2008-05-18 3:19 AM
devilboy - 2008-05-17 3:26 PM
BATMAN - 2008-05-17 7:23 AM
Is this an easy off piece? I like the look, but am wondering where it attatches and if it pops off easily. Thanks.
NOT at all.... you have to remove trunk(duh) and passenger back rest bolts into 4 holes in frame.
the luggage rack bolts onto back rest and should be done before you bolt down backrest.
to top it off you have to cut out 2 grooves in closeout panel(dremel cut off wheel or jig saw)
Measure twice and cut once....
mine is off by about 1/8 in on one side...
1/8"? Dont be getting all anal on us now.
Not getting Anal. I have been there my whole life |
|
| |
|
Puddle Jumper
Posts: 15
Quincy Massachusetts | I second that opinion, this is an essential accessory for a Vision Street that is Stratispherically priced for what it is. Your passenger may also find that it is too short. I have installed the stock passenger backrest on my Vision and found it lacking, I am going to build a custom piece that is a lot taller and can accomodate 2 more speakers. |
|
| |
|
Visionary
Posts: 1324
So Cal | VisionTex - 2008-05-18 8:08 AM
I have seen two types of rider back rests for the Vision, in the first phote, Chandler Tom has this type which is very nice, but somewhat high maintenance.
In the second photo you have the type I have which is lower in maintenance cost, but has a lot less features. Both are Visionary.
Got the first backrest before I got the Vision. Definitly the more expensive route. The fringe benifits were great 'till I got a license for it. Still not too bad, but definitly high maintenance.
Dont think an exchange would be good for my health.
|
|
| |
Vision Backrest/luggage rack question
