|
|
Puddle Jumper
Posts: 19
Maylene, AL | How difficult is it to install the Lighted Badges? |
|
| |
|
Cruiser
Posts: 142
| not really difficult, just time consuming with lots of screws....you have to remove most of the plastic (fairing) to access the back of the side fairing where you screw the badges... |
|
| |
|
Visionary
Posts: 4278
| you don't say what year you have.
you don't say if one burned out.
So if we new more we could cut hours out of your time if you told us more |
|
| |
|
Puddle Jumper
Posts: 13
Moweaqua, IL United States | not the same guy, but one of Mine burnt out on me this week... How big of a pain is it to get to the bulb? is there one? |
|
| |
|
Visionary
Posts: 4278
| Scotr3 - 2013-11-29 11:26 AM not the same guy, but one of Mine burnt out on me this week... How big of a pain is it to get to the bulb? is there one? There is a slot just under the housing so a flat screw driver can pop off the outer half. You will have to take the top plastic off to get at the conectors. There is no bulb its LED's and there not cheap $143 bucks |
|
| |
|
Visionary
Posts: 1228
Rancho Cucamonga, CA | If you still have a warranty, they should cover it. It is not a light bulb and should last longer than the bike. Mine was covered under an extended warranty. |
|
| |
|
New user
Posts: 2
| Well the issue is one thing that not enough persons are speaking intelligently about. I am very completely satisfied that. |
|
| |
|
Visionary
Posts: 3773
Pittsburgh, PA | Scotr3 - 2013-11-29 11:26 AM
not the same guy, but one of Mine burnt out on me this week... How big of a pain is it to get to the bulb? is there one?
the burnt out light is NOT serviceable ! How do i know? because i wasted the time a few years ago and found this out first hand... =( There is a little flat led light embedded onto the printed circuit board. I even tried to look up part numbers and went to radio shack to find something that would fit.. it was a total waste of time.... |
|
| |
|
Puddle Jumper
Posts: 13
Moweaqua, IL United States | thanks guys... guess I have some change to spend...
|
|
| |
|
Visionary
Posts: 1350
| Can't the LED be desoldered from the board? Maybe look under MIL SPEC LEDs for replacement? |
|
| |
|
Iron Butt
Posts: 623
| My left side is now out, after reading this thread I will keep it that way. Bike runs great without them. : ) |
|
| |
|
New user
Posts: 3
| Nozzledog - 2013-11-30 1:40 AM
If you still have a warranty, they should cover it. It is not a light bulb and should last longer than the bike. Mine was covered under an extended warranty.
The outer portion (plastic chrome) of the side badge on the left side of my 2011 Tour just fell off while riding (I never found it), leaving two wires coming out of the black base. My extended warranty (polaristar) rejected the claim saying they don't cover "body parts" or "lights". Pretty disappointing.
The dealer wants $370 to replace it. I see them (looks like they're only sold in sets) on ebay for $175-$200.
Question: should I buy a new one, then take off the outer chrome portion (which I assume has the light) and glue it onto the base after connecting the wires? Or should I tear off the fairing, etc. and replace the whole unit?
I just ordered the shop manual. I'm "average" in terms of mechanical ability and have no experience working on the Vision. Is this a tough job?
Thanks!!! |
|
| |
|
Visionary
Posts: 3773
Pittsburgh, PA | I can't remember how I was able to get mine off without removing body panels.. it's been at least 4-5 years now.... |
|
| |
|
Visionary
Posts: 1365
Central Maryland | Someone on this board posted a very cheap way to replace those lights in the badges with something else. Do a search. |
|
| |
|
New user
Posts: 1
| On another post shared for this topic I spotted for repair with pictures... http://www.vision-riders.com/bb/forums/thread-view.asp?tid=15078 |
|
| |
|
Visionary
Posts: 1365
Central Maryland | That's it !!!!
|
|
| |
|
New user
Posts: 3
| Thanks for the replies. The outer portion of my badge came off while riding and broke free from the wires. So I have no choice but to buy a new one. I think I'll try to just replace just the outer portion. I do hate to break apart the new one, but it sounds like that will be easier than taking off the body panels and replacing the whole thing.
Thanks again! |
|
| |
|
New user
Posts: 3
| Oops...accidentally hit submit twice. Sorry
Edited by OdentonVision 2014-08-31 12:22 PM
|
|
| |
Victory lighted badges
