|
|
Cruiser
Posts: 94
Las Vegas | I bought a set of bar ends. I think they look good in black. I haven't permanently put them on yet because I don't have the right screws. I partly put them on just to see what they look like and really like them.
Here is my question. When I had the stock bar ends off, I noticed they are about 4X heavier then the new ones. The new ones are aluminum. I'm not sure what the stock ones are made of. Are they heavy for a reason? Does it help stop vibration? I will try them out when I get the new screws but just thought I would ask here.
(barend1.JPG)
(barend2.JPG)
Attachments
----------------
 barend1.JPG (72KB - 5 downloads)
barend2.JPG (58KB - 2 downloads)
|
|
| |
|
Iron Butt
Posts: 1109
| They're there to reduce vibration. |
|
| |
|
Cruiser
Posts: 94
Las Vegas | They are the same diameter. I know it doesn't look it in the picture. |
|
| |
|
Cruiser
Posts: 94
Las Vegas | kris1956 - 2012-07-23 12:48 PM
They're there to reduce vibration.
That's what I was thinking. Sucks, I will probably keep the stock ones. I will still try the new ones though. |
|
| |
|
Puddle Jumper
Posts: 33
| DetroitDetomaso - 2012-07-23 3:00 PM
kris1956 - 2012-07-23 12:48 PM
They're there to reduce vibration.
That's what I was thinking. Sucks, I will probably keep the stock ones. I will still try the new ones though.
Been looking for some new bar ends. Where did you buy them??
Thanks |
|
| |
|
Visionary
Posts: 4278
| The stock bar ends are stainless steal. Yes they might take a way some vibration but you'll never know till you try. |
|
| |
|
Cruiser
Posts: 94
Las Vegas | Udnudn1968 - 2012-07-23 3:25 PM
DetroitDetomaso - 2012-07-23 3:00 PM
kris1956 - 2012-07-23 12:48 PM
They're there to reduce vibration.
That's what I was thinking. Sucks, I will probably keep the stock ones. I will still try the new ones though.
Been looking for some new bar ends. Where did you buy them??
Thanks
EBay, they are only about $10 shipped. Cheap |
|
| |
|
Cruiser
Posts: 94
Las Vegas | johnnyvision - 2012-07-23 3:33 PM
The stock bar ends are stainless steal. Yes they might take a way some vibration but you'll never know till you try.
I will give it a shot.
|
|
| |
|
Puddle Jumper
Posts: 33
| I saw those on Ebay but looked at my bar ends and they didnt look like they fit. Are they held on by a single bolt in the center or what? I also put in Vision on the auction page and it said they didnt work. If you can, send me a link for your auction. If you say they fit, then I will get a set.
Thanks a lot!
Steve |
|
| |
|
Cruiser
Posts: 160
Lennox, SD | Took my bar end weights off 2 years ago. No more vibration than before. |
|
| |
|
Puddle Jumper
Posts: 33
| Udnudn1968 - 2012-07-23 6:12 PM
I saw those on Ebay but looked at my bar ends and they didnt look like they fit. Are they held on by a single bolt in the center or what? I also put in Vision on the auction page and it said they didnt work. If you can, send me a link for your auction. If you say they fit, then I will get a set.
Thanks a lot!
Steve
Shoot, I'd even buy your old ones if they fit an 2008! |
|
| |
|
Cruiser
Posts: 94
Las Vegas | Udnudn1968 - 2012-07-23 4:12 PM
I saw those on Ebay but looked at my bar ends and they didnt look like they fit. Are they held on by a single bolt in the center or what? I also put in Vision on the auction page and it said they didnt work. If you can, send me a link for your auction. If you say they fit, then I will get a set.
Thanks a lot!
Steve
You have to mod them. I ordered new screws from the dealer yesterday. I will post how I did it after I get the screws. |
|
| |
|
Cruiser
Posts: 94
Las Vegas | Kioti - 2012-07-23 4:53 PM
Took my bar end weights off 2 years ago. No more vibration than before.
Cool! I hope its the same for me. |
|
| |
|
Puddle Jumper
Posts: 33
| DetroitDetomaso - 2012-07-25 8:22 AM
Udnudn1968 - 2012-07-23 4:12 PM
I saw those on Ebay but looked at my bar ends and they didnt look like they fit. Are they held on by a single bolt in the center or what? I also put in Vision on the auction page and it said they didnt work. If you can, send me a link for your auction. If you say they fit, then I will get a set.
Thanks a lot!
Steve
You have to mod them. I ordered new screws from the dealer yesterday. I will post how I did it after I get the screws.
Look forward to see your report! |
|
| |
|
Puddle Jumper
Posts: 33
| Any progress on this yet?? |
|
| |
|
Cruiser
Posts: 94
Las Vegas | I don't have the screws yet. Maybe I can pick them up this weekend. It so hot in Vegas its hard to care. I will get around to it soon. |
|
| |
|
Visionary
Posts: 4278
| Go to hardware store and get some. Hardware stores carry metric bolts of all sizes |
|
| |
|
Cruiser
Posts: 94
Las Vegas | johnnyvision - 2012-08-04 4:24 PM
Go to hardware store and get some. Hardware stores carry metric bolts of all sizes
I orderd them from the dealer for only 99 cents each. |
|
| |
|
Cruiser
Posts: 122
Westchester Co., NY | The new bar ens are sharp looking. |
|
| |
|
Visionary
Posts: 4278
| Pull your stock bar end you'll see there pretty much flat. So you want ones that are flat not the ones that go inside the bars.
By the way hardware store you can get 3 for a buck. Screw the over priced dealer an why weight a week or two. |
|
| |
|
Cruiser
Posts: 94
Las Vegas | Stoped at the dealer Friday. My screws are not in yet. |
|
| |
|
Visionary
Posts: 4278
| DetroitDetomaso - 2012-08-12 10:58 PM Stopped at the dealer Friday. My screws are not in yet. Screw the dealer let him have your dollar and go to the hardware store. Why do guys think you can only get bolts and bulbs at the dealer. We buy oil filters at a auto store look at hardware stores Lowell's fleet farm. Think out side the box guys. |
|
| |
|
Puddle Jumper
Posts: 33
| DetroitDetomaso - 2012-08-12 10:58 PM
Stoped at the dealer Friday. My screws are not in yet.
Let us know when you get them.
Thanks
Steve |
|
| |
|
Cruiser
Posts: 94
Las Vegas | I have them. Just need to get to it. I will try soon Steve.
|
|
| |
|
Puddle Jumper
Posts: 33
| Thanks.....much appreciated!
Steve |
|
| |
Bar ends.
